cut edge
英 [kʌt edʒ]
美 [kʌt edʒ]
网络 割边; 切边; 切割边的方法; 割边或桥; 切割边
双语例句
- A lot of people can cut brush at the edge of the field and stick that into the soil on the south and west side of the plant and provide some shade.
或者用灌木丛，换句话说，也就是枝条。把枝条砍成一米长，插到植物南面和西面的土壤中。 - To cut the leading edge of the pie slices in a simple circle pattern, an image is created with a transparent circle in the middle.
为了切去简单圆形图案中饼图分区的前缘，将创建一张中间带有透明圆形的图像。 - A notch or jagged cut in an edge. Comparative study of masticatory efficiency between attachment dentures and clasp removable partial dentures
锯齿状缺口物体边缘V形或锯齿形的缺口附着体义齿与卡环可摘局部义齿咀嚼效率研究 - California is on the cut edge of trend that spreads nationwide.
加州走在全国流行的尖端。 - This would be a bit more obvious if we cut the rhomb to have edge of equal axis.
若把斜方体的棱都切成等长，就可以看得更清楚。 - The bales may be stacked, cut edge down in a chamber, if walls are available.
如果有墙，草捆可以堆放在棚内，缩短周边。 - It cut deep: the edge of the blade reached to the back of his throat.
这一砍砍得极深，锋刃已经触及到喉部后侧。 - Production mechanism and rising law of water cut for edge and bottom water reservoir
边底水油藏开采机理与含水上升规律底部边距，底边，底线 - The rear perforations are visible on the cut edge.
后方齿孔都是看得见，对切缘。 - Cut a zigzag or scalloped edge on ( sth)
将（某物）的边剪成锯齿形或扇边形。 - Next, cut from the outside edge of the circle to the inner circle, as shown.
然后，从圆的外边缘到内孔剪一个口，如图所示。 - Bleed: Area of colours or photographs that extend beyond the cut edge of a page. The bleed allowance beyond the trimmed size is usually 3 mm or 1/ 8 inch.
出界：相贬或底色范围伸出页边裁切线以外者。出界宽限通常是完成尺寸加3毫米或1/8时。 - Results Two of 18 cases were negative in Lugol's coloration, in which pathologic check was cut edge cancer of esophagus in 1 case, the other case was high-not representative hyperplasia.
结果18例中，2例食管切缘粘膜卢戈氏液染色阴性，病理检查食管切缘癌浸润1例，食管切缘部分上皮高度不典型增生1例； - Development of Cut Edge Joint Belt
切边联组带的研制 - It is shown that the edge contact width is not always equal to the thickness of the wheel like conventional cylindrical grinding process, the point grinding angles and the depth of cut influence the edge contact width and surface roughness evidently in quick-point grinding process.
结果表明：与普通外圆磨削不同，砂轮周边与工件实际接触宽度并不恒等于砂轮宽度，点磨削变量角度和磨削深度显著影响砂轮周边的实际接触宽度与工件表面粗糙度数值。 - Measure the linear expansion coefficient of metal by interference of cut edge
利用光的干涉测金属体线胀系数的方法 - Development of Cut Edge V-Belt
切割式V带的研制 - The bilateral margins of the lesions were perpendicular to the pleura with a straight cut edge.
病灶两侧缘垂直于胸膜呈刀切样平直边缘； - A new type cut edge V-belt was developed by using advanced manufacture technology.
使用先进生产工艺研制了一种切割式V带。 - That the stay of relative slip between the metal being cut and the cutting edge is one of the main causes leading to the initiation of the crack near the cutting edge;
被切金属和切削刃之间停止相对滑动是导致刃前区产生裂纹的主要原因之一； - A 3-Restricted edge cut is such an edge cut that separates a connected graph into a disconnected one with each component having order at least 3. Graphs that contain 3-Restricted edge cut are characterized in this paper.
3限制性边割将连通图分离成不连通图，使其各连通分支含有至少3个顶点.含3限制性边割的图在本文中得到刻划。 - Excitation Filter with High Signal-to-Noise Ratio and High Steepness in the Cut-off Edge
一种高信噪比和陡截止边缘的激光滤光片 - The Calculating method of ideal surface roughness of part with round contour cut by cutter with round edge is proposed based on calculation of the roughness of part with linear contour cut by such type cutter.
在圆弧刃刀具切削直线廓形时理论粗糙度计算的基础上，着重研究圆弧刃刀具切削圆弧廓形时理论粗糙度的计算方法。 - The trailing-edge loss of radial inflow turbine stator was discussed based on the loss models of NASA, showing that the loss increases linearly with the trailing edge thickness. Thus, an efficient method of reducing trailing-edge loss is to cut down the trailing edge thickness.
基于NASA损失模型分析了径向透平静叶的尾缘损失，损失随着出口边厚度呈线性增加，减小出口边厚度是减小尾缘损失的有效方法。 - In ultrasonic cutting process, the cutting pressure is still essential for achieving good quality cut edge compared with traditional mechanical cutting process.
在超声切割过程中，为了保证切割质量，对切割压力仍有一定的要求。 - Through micro analysis, X-ray analysis and electronic scanning, it is found that the fatigue cracks initiate at the cut edge of the plated surface rather than at the joined area of the plating and the base material.
通过宏观断口分析、x射线应力分析、电子扫描分析，发现疲劳裂纹的萌生点在镀层表面的切削刀痕处，而不是镀层与母材的结合面上。 - The kinematics analysis of shear structure mainly includes the running track 、 velocity and acceleration of flying shear cut edge.
剪切机构的运动学分析，主要包括飞剪剪刃的运行轨迹、速度以及加速度的计算。